Hey there! As a supplier of film blowing machines, I often get asked about how to store these machines when they’re not in use. It’s a crucial topic because proper storage can significantly extend the lifespan of your equipment and save you a ton of money in the long run. So, let’s dive right into it. Film Blowing Machine
Pre – storage Preparation
Before you even think about storing your film blowing machine, you need to do some prep work. First off, give the machine a thorough cleaning. Run it for a short while with a cleaning compound if possible. This helps to flush out any residual plastic from the extrusion process. Once it’s cooled down, use a soft brush and a mild detergent to clean the exterior. Pay special attention to areas where plastic might have dripped or stuck, like the die head and the cooling rings.
Next, check all the parts for any signs of wear and tear. Look at the screws, belts, and gears. Tighten any loose screws and replace any parts that are showing excessive wear. This is also a good time to lubricate all the moving parts. Use a high – quality lubricant recommended by the machine’s manufacturer. Lubrication reduces friction and prevents rust during storage.
Choosing the Right Storage Location
The storage location is super important. You want a place that’s dry, clean, and well – ventilated. A humidity – controlled environment is ideal because high humidity can cause rust and corrosion on the metal parts of the machine. Avoid storing the machine in a damp basement or an area prone to flooding.
If you’re storing the machine outdoors, make sure it’s covered with a heavy – duty tarp. But even with a tarp, outdoor storage is not the best option as it exposes the machine to the elements. If you have to store it outside, try to find a sheltered spot, like under a carport or a shed.
Disassembling and Packaging
For some film blowing machines, it might be a good idea to disassemble certain parts for storage. For example, you can remove the die head, the screws, and the cooling fans. This not only makes the machine easier to move and store but also reduces the risk of damage.
When disassembling, make sure to label all the parts clearly. You don’t want to end up scratching your head later trying to figure out where each part goes. Once you’ve disassembled the parts, wrap them in anti – static bubble wrap or a similar protective material. This helps to prevent scratches and damage during storage.
Protecting the Electrical Components
The electrical components of the film blowing machine are very sensitive. You need to take extra care to protect them. First, make sure to disconnect the power supply completely. Then, cover the electrical control panel with a plastic sheet to keep out dust and moisture.
If possible, store the electrical components in a separate, dry area. This reduces the risk of short – circuits and other electrical problems. You can also use a desiccant pack in the storage area to absorb any excess moisture.
Long – term Storage Considerations
If you’re planning to store the machine for a long time, there are a few additional steps you should take. First, perform a full maintenance check before storage. This includes changing the oil, checking the filters, and inspecting the hydraulic system if your machine has one.
You might also want to consider applying a rust – preventive coating to the metal parts. There are many products available on the market that can provide long – term protection against rust. Just make sure to follow the manufacturer’s instructions when applying the coating.
Regular Inspections
Even when the machine is in storage, it’s important to conduct regular inspections. Check the machine every few months to make sure there are no signs of damage, rust, or pest infestation. If you notice any issues, address them immediately.
During these inspections, you can also turn on the machine briefly (if it’s safe to do so) to ensure that all the components are still functioning properly. This helps to prevent any parts from seizing up due to long – term inactivity.
Bringing the Machine Back into Service
When you’re ready to use the film blowing machine again, there are a few steps you need to take. First, remove all the protective packaging and clean the machine one more time. Check all the parts to make sure they’re in good condition and properly installed.
Then, perform a test run. Start the machine at a low speed and gradually increase it to the normal operating speed. Monitor the machine closely during the test run to make sure everything is working as it should. If you notice any problems, stop the machine immediately and troubleshoot the issue.
Why Choose Our Film Blowing Machines
At our company, we’re not just about selling film blowing machines. We’re committed to providing our customers with the best possible support, including advice on storage and maintenance. Our machines are built to last, but proper storage is still key to getting the most out of them.
If you’re in the market for a new film blowing machine or need some advice on storing your existing one, don’t hesitate to reach out. We have a team of experts who are ready to answer your questions and help you make the right decisions.
Whether you’re a small business looking to expand your production or a large manufacturer in need of high – quality equipment, we’ve got you covered. Our film blowing machines are designed to be efficient, reliable, and easy to operate.
Inspection Rewinding Machine So, if you’re interested in learning more about our products or have any questions about film blowing machine storage, just drop us a line. We’re here to help you every step of the way.
References
- Manufacturer’s manual for film blowing machines
- Industry best practices for equipment storage
- Technical guides on film blowing machine maintenance
Zhejiang Deguang Machinery Co., Ltd.
With abundant experience, we are one of the most professional film blowing machine manufacturers and suppliers in China. Please rest assured to wholesale high quality film blowing machine at competitive price from our factory. If you have any enquiry about cooperation, please feel free to email us.
Address: No.501, West Wangdong Road, Shangwang Street, Ruian City, Zhejang Province, China
E-mail: swdg@wenzhouhg.com
WebSite: https://www.deguang-machine.com/
